What kind of automatic slitting machine is better? Many customers will get stuck in the purchase process, let's take a look together.
There are two major types of automatic slitting machines, including domestically-made slitters manufactured in China and imported slitters imported from foreign technologies. So is it better to use domestic ones or import ones, in fact, in the world There is no best equipment, only the equipment that suits you best, and specific problems need to be analyzed. The performance of the imported slitter is relatively good, but the cost is not affordable for everyone, and the biggest disadvantage is the after-sales service. If there is a problem, what should be done in terms of maintenance? Therefore, it cannot be compared with domestic equipment. The domestic slitter is also fully automatic slitter, paper slitter and high-speed slitter. The technology of the domestic slitter is now more and more mature, which can basically meet the domestic slitting demand.
For how to use the automatic slitting machine, many people can't tell why. The following slitting machine manufacturers will tell you how to use the automatic slitting machine correctly?
When using the slitting machine, when you turn on the power, you must first check whether the static elimination mode has been turned on. This is to prevent the machine from malfunctioning and causing unnecessary losses during operation. (Static mode will control the system). Next, turn on the air pressure switch of the slitter and adjust it to between 0.5 and 0.6. The adjustment of air pressure is very critical, because it will affect the stability of operation. After adjustment, use three to six cones to place the mother roll in the roll section.
After the mother roll is placed in the roll section, the machine should be debugged, the diameter of the mother roller should be compared, press the up or down button, adjust the unwinding rack to the appropriate height, and then clamp the roll film to make it It can rotate at a constant speed or quickly, and then press the height adjustment button again to confirm the safety. Then to install the blade, first check the blade edge of the blade to see if there is any damage, and then select the appropriate cutting method according to the needs and adjust the placement of the blade. After this step is completed, the paper core module can be debugged.
The adjustment of the paper core is to enable the paper to be placed in a relatively correct position, so that the cut pieces of paper will be very uniform. After all the commissioning work is completed, a unified trial operation of the slitter should be carried out. When the trial production products have no problems, they can be used.
After reading the above, I believe everyone already knows the correct use of the automatic slitter.
Regarding the precautions for the use of the slitter, many people do not understand it comprehensively. Only after you have really understood this knowledge can you better use the slitter.
1. Safe production is a necessary prerequisite, and safety matters must be paid attention to during operation.
2. When the original paper is cut to the end, slow down properly to avoid paper break.
3. Shut down for help if you cannot solve the problem, do not continue to run the machine under abnormal conditions.
4. When the core of the base paper is deformed and the base paper rotates slowly, pay attention to the speed adjustment to reduce the speed as much as possible.
5. When blowing, first stop the machine and put the paper into the tube, then restart the machine.
6. When encountering abnormal problems and want to stop the machine, you must press the red key for emergency stop. Develop the correct emergency shutdown habit.
7. Pull out the gas shaft separately, and support water pipes must be added on both sides. Pay attention to pull out the gas shaft safely.
8. For problems with some base paper cores, pay attention to proper chuck clamping of the base paper core.
9. When loading the original paper, when the original paper passes through the cutter, the paper rolls up when the paper rolls up, and then the paper must be adjusted.
10. In the case of paper padding, keep a certain distance from the plastic shaft and the paper tray to avoid injury.
11. When blowing, pay attention to the stability of the flash when accelerating.
12. When adjusting the knife, first use an air gun to clean up the dust, and then perform the knife adjustment process.
13. When using the knife slide to deal with the damaged paper of the base paper, be careful not to damage the inner paper.
14. When using an air gun to clean the dust on the knife, first try spraying it out for a while to drain the water. If the gas from the air gun contains water, use a rag to dry the shaft before continuing.
15. In case of category C paper, try to slow down the speed as much as possible to avoid paper breaks (1200 revolutions and 1800 revolutions are 5 minutes slower when the paper is removed and then the time difference is 7 minutes).
All in all, the slitter must pay attention to the above content during use.
The working efficiency of the slitting machine is closely related to many factors, so in order to better use, we need to understand these factors. Let's take a look at the working efficiency of the slitting machine manufacturers.
The working efficiency of the slitting machine is related to the following factors: slitting speed, finished product rate, non-operation occupancy time, stability, etc. The cutting speed of the high-speed cutting machine is an important indicator of the working efficiency of the cutting machine, but if the yield is low, it will not only cause the working efficiency of the whole machine to be low, but also cause the cost to rise.
All in all, the working efficiency of the slitter is related to the above content.
The application of slitting machines in our country is already very extensive. This product is designed in many fields, and some problems are easy to occur in use. The following slitter manufacturers share two common problems.
Why is the paper tray cut to the right protruding for a while?
1. When starting to run, the edge of the paper is not tight, you can properly pad the paper when the machine starts cutting to avoid
2. The inner diameter of the paper core added to the paper core is too large, so that the paper core cannot be locked after the expansion of the air shaft so that the paper core slides when the rotation rotates to cause an offset. The solution is to check the inner diameter of the paper core when the paper core is placed on the inlet shaft. size.
Why does the base paper core shake even when it is not deformed?
Generally speaking, the slitting machine will not shake too much when the core of the base paper is not deformed, but if the chuck is forced to be clamped when loading the base paper, it will cause an imbalance on both sides. In this case, the operation control It will have a great impact, so when adding the paper chuck, pay attention to the balance of the paper core on both sides. Why do the paper trays at both ends sometimes have burrs?
The width of the base paper will generally be 3-5mm larger than the size marked on it. Under special conditions, it will jump out of this range. If the size of the base paper is 1185mm, we will adjust the knife to 1190. In the case of the base paper may be greater than 1190, the side paper tray There will be glitches. In this case, you can first stop and loosen the knife for a while, wait for a while, and tighten the knife on both sides.
I believe everyone knows these two common problems.