What do you know about the installation steps of the slitter rewinder? The device of slitting and rewinding machine After unpacking, you should check the integrity of the machine, check whether there is any damage during transportation, etc. After checking the damage, you can install the correction level on a flat and solid basis. After the device is calibrated, check all parts to see if they are intact, whether the connecting bolts are tightened reliably, and whether the moving parts are sensitive. Then add corresponding lubricants to each lubricating part. ， Before turning on the slitter rewinder, please read the attached manual carefully. Work slowly at the beginning, and gradually increase the cutting speed until everything is normal.

        How to make the automatic slitting machine last longer? Then do the daily maintenance, specifically how to do it?
        The automatic slitting machine should keep all parts intact. The slitting equipment is generally composed of multiple parts. If it is less or damaged, it will not make our slitting equipment work well. Long-term wear and tear may make the equipment lose its ability to work, so no matter which one If the parts are damaged, we will not be able to use them normally. You must keep the parts of the slitter intact when using them.
        Our automatic slitting machine should be cleaned in time. If our slitting equipment is left unattended for a long time, it will seriously affect the integrity of his surface. Many times, if the dirt on the surface of the slitter is not cleaned in time, the equipment will gradually undergo chemical and physical changes. The device will not work properly.

        When buying an automatic slitting machine, we must compare the brand and word of mouth, which helps us to buy products better.
        1. Compare the brand of automatic slitting machine
        We should compare the automatic slitting machines of different brands, because the brand is a benchmark and a standard in the industry. We can use the big brands as a basic point. When comparing, we will find the differences. It's important to say that we can discover the impact, at least for us this is a brand new experience, and everyone agrees very much.
        2. Understand the reputation of the automatic slitting machine
        The quality of a product has a lot to do with its word of mouth. The customers who have used it are the best inspectors. It can ensure the quality and performance of the product. It also brings us the best reference standard. Don't think that all of this is very simple. In fact, there are still certain requirements for us. Be patient. Try to understand the process structure and working principle of various aspects of the product, understand the properties of the materials used, and so on.
        After reading the above content, I believe everyone already knows the brand and word of mouth that you need to know to buy a fully automatic slitting machine.

        What are the operation items of the automatic slitting machine? I do n’t know if you are familiar with the slitting machine. What is the characteristics of the automatic slitting machine? What are the specific procedures? These are questions that many people have always had. I will help you to give a detailed introduction to the operation rules of the slitting machine. I hope to help you.
        1. Turn on
        1. Turn on the electrical isolation switch (set in front of the electrical control cabinet), press the EMERCENCY STOP RESET and READY TO RUN buttons, the key opens the MACHINE to RUN (on the main console) to check whether the voltage (380V) and current are correct and stable.
        2. Turn on the power switch of the hydraulic system (set on the main hydraulic drive frame), and check whether the oil level and pressure gauge of the main hydraulic drive system are correct and stable.
        3. Open the pneumatic shut-off valve (set on the air inlet pipe under the pneumatic control cabinet), check whether the air pressure is correct (not less than 6.0bar) and stable.
        2. Setting control
        1. Set the slitting menu according to the film type, thickness, length, width, etc. arranged in the slitting plan.
        2. File the corresponding BOPP film file from the PDF.
        3. Set the winding length and width of the film with corresponding specifications.
        4. Select the corresponding winding station, adjust the roller arm and roller, and install the paper core of corresponding specifications.
        3. Feeding, film passing and film joining
        1. Feeding: According to the requirements of the cutting plan, according to the driving operation regulations, according to the actual situation, hang the corresponding parent roll on the aging frame, and choose the direction according to the inside and outside of the corona surface. The control button clamps the steel core, leaving the steel core support arm and driving.
        2. Film penetration: When there is no film on the slitter, film penetration is required. Using the slitting device and function keys of the slitting machine, tie one end of the original film to the ring eye of the threading chain, and activate the filming button, so that the film is evenly distributed on each roller along the slitting process.
        3. Film connection: when there is film on the slitting machine, when changing the roll joint, use the vacuum film connection table to start the film connection table to the working position, manually flatten the film on the first traction roller of the cutting machine and start the upper vacuum pump Suction the film to make the film flat to be adsorbed on the film receiving table, attach double-sided tape and cut off the excess film under the tape, flatten the film on the unwinding rack and start the lower vacuum pump to make the film flat to adsorb, remove the tape Put on the paper layer and level the adhesive film. The joints should be neat and wrinkle-free. Then turn off the upper and lower vacuum pumps, and open the film receiving table to the inoperative position.
        Four, start-up operation
        1. Change the specifications, install the paper core on the inner and outer winding arms, and notify all personnel to leave the machine when the pressure roller is in the operation preparation state to prepare for operation.
        2. Put the ANTI-STAIC BARS on the main console to AUTO, READY TO RUN is turned on, and MACHINE RUN is started to start the operation.
        5. Slitting control
        In the process of slitting operation, carefully monitor and observe the effect of slitting, and properly adjust and control the slitting speed, unwinding tension, contact pressure, curved roller, edge traction roller, and guide edge.
        6. Receipt
        1. When the machine stops running after the inner and outer ends are wound up, use the unloading button to place the film on the prepared film unloading trolley, cut the film and paste the film roll with sealing glue.
        2. Use the chuck release button to loosen the chuck, check whether the paper core of each film roll is away from the paper core, and if one end is still stuck on the paper core, manually remove the film roll.
        3. Make sure that all the films leave the chuck and place on the trolley, use the film loading button to raise the winding arm, install the corresponding paper core, and attach the film neatly to the paper core for the next slitting.
        7. Parking
        1. When the film roll reaches the set length, the equipment will automatically stop.
        2. During the operation of the equipment, press MACHINE STOP to stop as needed.
        3. When a quick stop is required, press the MACHINE STOP key greater than 2S.
        4. When there is an emergency situation such as equipment or human accidents, press EMERGENCY STOP for emergency stop.
        After reading the above knowledge about slitting machine, I do n’t know how much you have learned, but people who need to use slitting machine frequently in their work need to have a good look at this knowledge. It should be great for you. It helps.

        In the process of selecting a fully automatic slitting machine, many people have chosen inferior products for the price. Let's analyze with the editor which automatic slitting machine is better?
        When we choose a machine, the first thing to consider is the cost performance, the price is too high, it is not cost-effective, and it is too low and fears quality problems. Therefore, it is very important to choose an affordable price, and this machine must be practically solved, energy-saving and durable Because in a sense, energy saving and durability is also a major feature of environmental protection, which can reduce the family's long-term burden.
        When we choose the machinery of a factory, we must have a practical understanding from many aspects to see whether their reputation is good or not, and the quality is reliable. We can pay attention to the details of some products, such as the raw materials for the production of the product, and Product quality testing is very important, and it is worth considering whether the technology in production is advanced and reliable.
        After reading the above, I believe everyone knows the selection method of the automatic slitting machine.