During the use of the slitter, its tension will change. So what is the reason for the tension change of the slitter? The following slitting machine manufacturers share the factors of tension changes.
1. During the rewinding and unwinding process of the slitting machine, the diameter of the rewinding and unwinding is constantly changing. The change in diameter will inevitably cause the change of the tension of the raw material. Unwinding under the condition of constant braking torque, the diameter will decrease and the tension will increase accordingly. Rewinding is the opposite. If the rewinding torque is constant, the tension will decrease as the rewinding diameter increases. This is the main factor that causes the tension of raw materials to change during operation;
2. The change of the lifting speed of the machine will inevitably cause the change of the tension of the whole machine:
3. Non-uniformity of slitting raw materials. For example, the fluctuation of the material elasticity, the thickness change of the material along the width and length, the eccentric mass of the roll, and the changes in the temperature and humidity of the production environment will also affect the tension fluctuation of the machine;
4. The change in the tightness of the raw material coil will also cause the change of the tension of the whole machine;
5. The change in speed during slitting affects the change in tension: when the speed is increased or decreased during operation, the speed of the main motor changes. First, the tension of the material in the unwinding traction to the winding section is caused to change momentarily, and the material must be slightly vibrated after a period of time to gradually stabilize the tension. The instability of this tension is manifested by the uneven winding on the finished roll and the unevenness on the end surface, which affects the product quality.
6. The transmission mechanism of the slitting machine (such as guide roller, floating roller, flattening roller, etc.) has factors such as imbalance and unstable air pressure.
After reading the above content, I believe that everyone already knows the factors that change the tension of the slitting machine.
In today's life, there are many ways to buy slitting machines. We can buy them in nearby stores or through the Internet. These purchase methods have different advantages. So it is good to buy products from slitting machine manufacturers. ?
Find the direct sales of the slitting machine manufacturer, because we need to install it after the purchase, and if we buy this equipment in the big brand specialty store, they will demonstrate the specific operation process for us, and there will be a special person for us Deliver the equipment to your door and provide installation services. This service can help us solve many problems and save us a lot of troubles. So in life, if we find it troublesome, or if we don't know how to install it, we can buy it at a nearby specialty store.
Buying online, because the products sold on the Internet after all save the rent, employees' wages and other aspects, so the price will be lower when selling. And they will send this machine to their homes, so it is more convenient and appropriate.
After reading the above content, I believe that everyone already knows the advantages of purchasing products at the slitter manufacturer.
The operation of the slitting machine is not so simple. In order to make the slitting machine better used, we must understand the operation steps of the slitting machine. The following is the operation steps of the slitting machine manufacturers.
When you turn on the power, you must first check whether the static elimination mode is turned on. This is to prevent the machine from malfunctioning and causing unnecessary losses during operation. Next, turn on the air pressure switch of the slitter device and adjust it to 0.5 to 0.6. The adjustment of air pressure is critical because it affects the stability of the operation. After the adjustment is completed, use three to six cones to place the mother roll into the roll section. After the mother roll is placed in the roll section, the machine should be debugged, and then the roll film should be clamped so that it can rotate uniformly or quickly. Then, press the height adjustment button again to confirm the safety. The next step is to install the blade. First, check the blade edge of the blade to see if there is any damage, and then select an appropriate slitting method to adjust the placement position of the blade. After this step is completed, you can debug the paper core module.
The parts and components of each part of the slitting machine are very important. A little inconsistency may cause the cut-out paper to be not flat and the cuts to be kept concise. One-time slitting, so the quality of slitting equipment is very critical.
After reading the above content, I believe that everyone already knows the operation steps of the slitting machine.
In the practical application of the slitting machine, there will always be various problems. Some feel that it is caused by the old machine, but this is only an objective reason. So what else? The following slitting machine manufacturers tell you the reasons for frequent failures.
Generally, new machines are installed and debugged when they leave the factory. After quality inspection, they are shipped in split packaging. It's not just a question of level and proper installation, it's also a question of inspection and correction. The old machine should be more so. As for maintenance and use, I won't say much, just want to talk about the quality of maintenance:
Repair is not a simple disassembly, not only to find the cause of the failure, but also to find other problems associated with it.
The slitting machine has a strict time cooperation relationship, as well as assembly tolerances and adjustment values, and busy disassembly and excessive adjustment are the main reasons for the machine's accelerated wear and failure.
Purchasing and processing quality of spare parts. It is not necessary to use original spare parts for all parts and electrical components. Original parts have high costs and long procurement cycles. Unless special or critical spare parts, most other parts and electrical components can be replaced. As long as you understand the part processing technology and component characteristics.
At present, in many cities, the development of slitting machines is still in a relatively backward stage, so if slitting machine manufacturers want to change this situation, then they must make a transformation strategy, so how should they proceed?
I. Improve product quality and technology
Without perfect products as guarantee and support, slitter manufacturers cannot survive for a long time. The improvement of product quality and technology is fundamentally the innovation of talents, technology and business management. Slitting machine manufacturers should pay attention to the construction of corporate culture, integrate culture into products, corporate management, and marketing strategies, use culture to gather people's hearts, attract talents, and form the core business philosophy of the enterprise, and ultimately form the core of the enterprise in product quality and technology. Competitiveness.
Second, establish brand awareness
In today's era, who can attract the attention of more consumers and get more attention is already half done. The other half is how to turn this focus into real economic benefits. For enterprises, the added value of a brand is an important selling point that attracts consumer attention. In fact, the supporting point of brand strategy is the added value of the product, that is, the brand spirit. The so-called brand spirit can be understood as the spirit represented by each product. In addition to the practicality of the product itself, it brings a spiritual experience or concept to consumers.
In today's era, technological victory has passed, and has been replaced by "resonating with consumers" and "making unforgettable experiences for customers." Only by publicizing the spirit of the product can this kind of goods and functions penetrate into all aspects of consumers and even social life. If you want to successfully establish a brand, you must give the product a unique connotation, especially stainless steel products.
Third, innovation and change
Transformation is an innovative process that actively seeks new changes. In order for the slitting machine manufacturer to successfully transform, its operation and management must be brave to accept new things, have a keen market perception ability and a long-term development vision. It is important that the managers of slitting machine manufacturers need to continuously learn from books, from operators in the same industry, and from employees, to learn new knowledge of enterprise management and management, and to study the development of the industry. Only in this way can business managers not stand still, innovate and change, seek the right development path for the enterprise, and achieve successful transformation.
After reading the above content, I believe that everyone knows the transformation strategy of slitter manufacturers.