Slitting machines are developing in many places, so what are the main developments of slitting machines? The development of slitting machine manufacturers is analyzed below.
        The mission power of a slitter is a comprehensive concept. During the slitting process, the stable tension system of the paper slitting machine is a major goal to ensure product quality. The magnetic powder clutch and brake are a special kind of active actuator. The paper slitting machine is filled in the mission gap or film Cut into a moment, change the excitation current can change the magnetic condition of the magnetic powder, and then adjust the transmitted torque. It can be used for stepless speed regulation from zero initial to synchronous speed, suitable for high-speed segment fine-tuning and medium and small power speed regulation system. Paper slitting machine It controls the tension between unwinding, traction, slitting, winding, etc., so that the slitting data is always in a fluctuating state during the slitting process.
        Assuming that the tension control is stable, the paper slitter can prevent the original data from deforming and drifting during the process of the machine's speed increase and decrease. The General Assembly will form the sum of laborious and non-reeling tension of the reel for the next process. Most of the previous paper cutting machines used magnetic powder clutches to control the tension. However, the speed of the magnetic powder clutch cannot be high. The paper cutting machine is liable to form high-speed conflicts of magnetic powder when it is running. The frequency conversion motor is used to control the tension system of the slitting machine. The swing roller is used for active detection. The man-machine is at a low temperature. The paper slitting machine shortens its life.
        Following the development of technology, servo drive skills, etc., it divides the raw materials into several independent units. Its mission principle is to fix the raw materials on the unloading. One end of the unloading shaft is equipped with a magnetic powder tension controller to stabilize the raw materials. The required tension is then pulled through a pair of rubber rollers to pull the raw materials. The paper slitter is cut into several pieces by the blade. It is then guided to the A and B winding shafts by the guide rollers to stop the winding products.

        During the operation of the paper slitting machine, it is prone to many problems, so what are the problems? Let ’s take a look together.
        1. The lower roll of the slitter is connected with the two paper rolls. If the paper is not cut, it is a small problem that often occurs. If this problem occurs, you must first check whether the blade of the paper cutter is flawless. If not, check the paper cutter. Check whether the knife is attached to the bottom knife after the knife is loaded.
        2. When the cutting machine is not in the up position of the paper cutter, first check whether the external limit is normal, and then check the gear box of the paper cutter. If the oil level is too low and the rise is not enough, check the three-row chain of paper cutters. Not that the chain is stretched too much.
        3. When the manual cutting runout of the cutter blade of the slitter is large, remove the cutter head and replace the upper cutter shaft.
        4. When the cutter blade is attached to the roller during the ascent of the cutter of the slitter, first check whether the cylinders on both sides of the cutter are operating normally during the ascent. If one of the cylinders does not operate, the cutter blade will stick to the roller surface. The cylinder needs to be replaced.

        Regarding the maintenance method of the paper slitter, many people do not know the specific operation scheme, which has caused many paper slitter problems. Let's take a look at the maintenance method of the paper slitter together.
        First, the transmission device of the slitter, such as a gear chain, needs lubrication after a period of time.
        Second, in general, there is no problem with the slitting machine, and the consumable parts are just small gears. If a printing knife is added, the wool roll will become thinner after one and a half years of use and need to be returned to the factory for repair. If the coil embossing device of the slitter needs to be replaced, the coil needs to be transported back to the original factory for transformation, and the transformation cost is not high.
        Third, pay attention to the stability of the voltage, otherwise the motor is easy to burn out; pay attention to hygiene, do not let foreign matter fall between the steel roll and the rough roll.

During the operation of the automatic slitting machine, it has many precautions, so what are the main issues? Let ’s take a look together.
1. Before use, check the voltage, the correct and stable currents are equal.
2. Before the equipment is ready for operation, all nearby personnel must stay away from the equipment to ensure personal safety before operation.
3. Do not touch the film roll or film core with your hands. Do not draw a knife or hard object on each roller core. To avoid being caught in the machine in your hand, causing personal injury.
4. Regularly clean and inspect the machine. If the automatic slitting machine does not stop for a long time, wipe the surface and apply anti-rust oil to increase the service life.

        Now more and more places are cutting paper strips, and high-speed slitting machines are generally used. So what is the significance of this kind of cutting? What does a high speed slitter mean for a paper strip? Let ’s take a look together.
        A common use range of slitting machines is slitting paper strips. This paper slitting is very common in the market, and it is often used by many businesses. It is mainly to cut horizontally or longitudinally a very wide roll of material, so that it becomes a product with a flat area and a uniform size. Therefore, it is particularly suitable for the manufacture of related materials such as mica tape, paper, insulators and films. What industries can use slitting machines? Paper mills, printing plants, packaging plants are indispensable.
        Slitting machine is a kind of machine and equipment that can operate at high speed. Its operating speed can reach more than 300 meters per minute. Therefore, before using the equipment, you must carefully check the machine to see if the parts are damaged. Whether the machine can operate under power (whether the power is on).
        In addition, it should be noted that during work, it relies on the conversion of single and double blades. Because the requirements for the blades are relatively high, the blades must be checked before the machine equipment works. If there are no issues with these checks, production is ready.