What is the development and working conditions of the paper slitter? Let's take a look below.
The mission power of the slitter is a comprehensive concept. In the slitting process, the stable tension system of the paper slitter is a main goal to ensure product quality. The magnetic powder clutch and brake are a special type of active actuator. The paper slitter is filled with mission gaps or films Cut into moments, changing the excitation current can change the magnetic state of the magnetic powder, and then adjust the transmitted torque. It can be used for stepless speed regulation from zero preliminary to synchronous speed. It is suitable for high-speed section fine-tuning and medium and small power speed regulation system. The paper slitter controls the tension between unwinding, pulling, slitting, and rewinding, so that the slitting data is always in a fluctuating state during the slitting process.
Assuming that the tension control is stable, the paper slitter can prevent the original material from being deformed and drifting during the process of speeding up and speeding down. The pass will form the sum of the trouble of the next process and the tension of the unwinding shaft. Paper slitters used to use magnetic powder clutches to control tension. However, the speed of magnetic powder clutches cannot be high. When paper slitters are running, high-speed conflicts of magnetic particles are easily formed. Frequency conversion motor is used to control the tension system of the slitting machine. The swing roller is used for active detection. The man-machine is used for low temperature. The paper slitting machine shortens its life. When severe, it will be stuck and the machine will be blocked.
With the development of technology and the composition of servo drive technology. It is to divide the raw material into several independent units. Its mission principle is to fix the raw material on the discharge. One end of the discharge shaft is equipped with a magnetic powder tension controller to stabilize the raw material. The required tension is passed through a pair of rubber rollers to pull the raw materials. The paper slitter is cut into several pieces by the blade. Then it is guided to the A and B winding shafts by each guide roller to stop the winding product.
After reading the above, I believe everyone already knows the development of the paper slitter.
The mission power of the automatic slitter is a comprehensive concept. During the slitting process, the stable tension system of the automatic slitting machine is a main goal to ensure product quality. The magnetic powder clutch and brake are a special type of active execution components. The film is cut into moments, and changing the excitation current can change the magnetic state of the magnetic powder, thereby adjusting the transmitted torque. It can be used for stepless speed regulation from zero preliminary to synchronous speed. It is suitable for high-speed section fine-tuning and medium and small power speed regulation system. The automatic slitting machine controls the tension between unwinding, traction, slitting, and winding, so that the slitting data is always in a fluctuating state during the slitting process.
Assuming that the tension control is stable, the automatic slitting machine can prevent the original material from being deformed and drifting during the process of machine speed up and speed down. The pass will form the sum of the trouble of the next process and the tension of the unwinding shaft. Fully automatic slitting machines used to use magnetic powder clutch to control the tension, but the speed of the magnetic powder clutch cannot be high, and the high speed conflict of magnetic powder is easy to form during the operation of the automatic slitting machine. The vector variable frequency motor is used to control the tension system of the slitting machine. The swing roller is used for active detection. The man-machine is used for low temperature. The automatic slitting machine shortens its life. It will be stuck when severe, which will hinder the operation of the machine.
With the development of technology and the composition of servo drive technology. It is to divide the raw material into several independent units. Its mission principle is to fix the raw material on the discharge. One end of the discharge shaft is equipped with a magnetic powder tension controller to stabilize the raw material. The required tension is passed through a pair of rubber rollers to pull the raw materials. The automatic slitter is cut into several pieces by the blade. Then it is guided to the A and B winding shafts by each guide roller to stop the winding products.
In order to make better use of the automatic slitting machine, it is necessary to do the maintenance and operation of the automatic slitting machine, so what should be done? Let's take a look below.
1. Regular lubrication of the oil road should keep the road clean, which can greatly improve the work efficiency.
2. Regularly change the oil of the equipment, and also clean the oil filter device to avoid clogging.
3. Keep the parts of the automatic slitting machine clean, lubricated and flexible.
4. Keep the relay contacts of the device running properly, to avoid excessive dust affecting its function.
The above is the maintenance and operation of the automatic slitting machine.
At present, the development of the slitting machine is getting faster and faster. The traditional slitting machine has the problem that the speed of the magnetic powder clutch cannot be high, and the current automatic slitting machine has overcome the high-speed friction of the magnetic powder, which generates a lot of heat, resulting in card Dead, making the machine run wrong. Therefore, the automatic cutting machine is becoming more and more intelligent.
Its intelligence is mainly reflected in three aspects: intelligent in operation function; intelligent in process function; intelligent in after-sales service.
As a slitter manufacturer, of course, there will be a set of methods for maintaining products, so what are they?
1. Pay attention to safety when using it. Do not stretch your hand over the blade when the machine is turning.
2. Grease the lubrication holes regularly to prevent the rotating shaft from wearing due to lack of normal lubrication.
3. If the user needs a workpiece with a special cutting width, various types of special gaskets can be made.
4. When the rod nylon washer needs to be used for a long time, if the cutting burr is seriously damaged, it should stop working immediately, open it next to the cover, loosen the nut with a special wrench, loosen the screw, and remove the swing rod.
5. The power supply should be safely grounded to ensure no leakage.
The above is the maintenance method of the slitting machine manufacturer.