In our lives, there are often materials that need to be cut, and at this time, the appearance of a high-speed cutting machine is needed. Let's understand the cutting method of high-speed cutting machine and the choice of cutting tools.
Cutting method:
1. Cutting: the cutter is fed vertically, and the wide-width coil is cut into multiple rolls of narrow specifications;
2. Double speed feed: refers to cutting the material by cutting the material or tool in opposite speed.
3. Bevel cutting: according to the demand of material feeding, adjust the cutting direction of the cutting tool so that the cutting direction is not completely perpendicular to the material curling diameter;
4. Single speed feed: it means that the material or tool can be fed at any station speed, and the other station can keep the feed.
Tool selection:
1. Tungsten steel knife, which has good brittleness and sharpness, and is generally used for cutting soft materials such as double-sided tape. The cutting precision of the cutter is good, and there are few burrs and silk edges in the cutting process. However, this tool is prone to chipping for harder materials. In addition, the cost of knives is relatively expensive. Generally, manufacturers only use materials with relatively soft texture such as tape, PE film, and masking paper.
2. White steel knife, also known as high-speed steel knife. This kind of cutter has good toughness and high cutting efficiency, but the cutting sharpness is not good. Generally using this kind of cutter, it is necessary to adjust the speed properly to make up for the unsharpness that may be caused during the cutting process. This kind of blade is mainly used for cutting high hardness materials such as PET material and PE material. The price is relatively cheap, more practical, is a common tool.
All in all, the high-speed cutting machine has become an inseparable equipment in our lives.
Maintenance of high-speed slitting machine:
Before use, the main parts of the automatic slitting machine should be inspected and filled with lubricating oil; when checking and disassembling the automatic slitting machine, it is strictly prohibited to use unsuitable tools and unscientific operation methods; Perform a comprehensive cleaning and inspection; if the automatic slitting machine is not used for a long time, all bright surfaces must be wiped clean, coated with anti-rust oil, and covered with a plastic cover to cover the whole machine. If the full-automatic slitting machine is stopped for more than 3 months, the anti-rust oil should be covered with moisture-proof paper; after the work is completed, the equipment should be cleaned carefully, the exposed friction surface should be wiped clean, and lubricated.
Daily maintenance of slitting machine:
To do the daily maintenance and maintenance work of the slitting machine, the following five points should be done.
First, the electrical parts should be cleaned and inspected regularly to eliminate hidden dangers in time.
Second, the use of slitting machines is accomplished by slitting machines and cross-cutting machines. Therefore, high-quality slitting knives and cross-cutting knives should be used.
Third, the daily maintenance of the slitting machine should be in place, and its criterion is that it is smooth, clean, and clear (no dust, no debris) in place, to ensure that the sliding part of the device is in good condition.
The fourth is maintenance work. Periodic and irregular inspections of rotating parts should be stopped (especially real-time monitoring of wearing parts). Carry out regular adjustment, regular replacement, commutator and make detailed records to achieve the purpose of extending the service life of the equipment.
Fifth, to improve the technical quality and level of the personnel who operate the slitting machine, the operation of the control part should be assigned by a dedicated person, and no one can operate it without permission.
The automatic slitting machine should pay attention to many matters during the work, and also pay attention to maintenance, so how is it done?
1. Before the equipment is ready for operation, all staff members must stay away from the equipment to ensure personal safety before starting operation.
2. Before starting to check the voltage, the correct and stable current is equal.
3. Make a comprehensive cleaning and inspection of the machine on a regular basis. The automatic cutting machine has not stopped for such a long time. Wipe the surface and apply anti-rust oil, which can increase the service life.
4. Do not touch the film roll or roller core in operation by hand, do not draw a knife or hard object per roll core, in order to avoid being caught in the machine, causing personal injury.
Repair and maintenance of automatic slitting machine
1. Regularly change the oil of the automatic cutting machine and clean the oil line filter device to avoid part of the oil clogging.
2. Lubrication of the oil path of the automatic slitting machine is an important part of maintenance work. Paper machine oil to keep the road clear, so that the automatic cutting machine can work efficiently and orderly.
3. Keep the relay contacts inside the electrical control box of the machine clean to prevent the machine from running normally due to too much dust.
4. Keep the parts of the automatic slitting machine clean, lubricated and flexible so that it can clear the accumulation of ink on the machine in time, so the production efficiency is high.
All in all, the precautions and maintenance methods of the automatic slitter are very important.
What are the maintenance of paper slitting machine? Maintenance of paper slitting machine:
Before use, the main parts of the automatic paper slitter should be inspected and filled with lubricant; when checking and disassembling the automatic slitter, it is strictly prohibited to use unsuitable tools and adopt unscientific operation methods; The machine is fully cleaned and inspected once; if the automatic slitting machine is not used for a long time, all bright surfaces must be wiped clean, coated with anti-rust oil, and the whole machine is covered with a plastic cover. If the full-automatic slitting machine is stopped for more than 3 months, the anti-rust oil should be covered with moisture-proof paper; after the work is completed, the equipment should be cleaned carefully, the exposed friction surface should be wiped clean, and lubricated.
Daily maintenance of paper slitting machine:
To do the daily maintenance and maintenance work of the paper slitter, the following five points should be done.
First, the electrical parts should be cleaned and inspected regularly to eliminate hidden dangers in time.
Second, the use of paper slitting machines is accomplished by slitting machines and cross-cutting machines. Therefore, high-quality slitting knives and cross-cutting knives should be used.
Third, the daily maintenance of the paper slitting machine should be in place, and its criterion is that it is smooth, clean, and clear (no dust, no debris) in place, to ensure that the sliding part of the device is in good condition.
The fourth is maintenance work. Periodic and irregular inspections of rotating parts should be stopped (especially real-time monitoring of wearing parts). Carry out regular adjustment, regular replacement, commutator and make detailed records to achieve the purpose of extending the service life of the equipment.
Fifth, improve the technical quality and level of the personnel who operate the paper slitter. The operation of the control part should be assigned by a person, and no one can operate it without permission.
What are the technical parameters of the slitter? The following slitter manufacturers will talk to you about it.
The slitting machine must apply a certain amount of stretch and tension to the aluminum foil, and the control force of the tension aluminum foil is the tension. Products are becoming more and more popular, and the improvement of performance is inseparable from the development of technology. Its common products are used in many industries, and there are many manufacturers in Wenzhou that manufacture their products. The price is also due to processes and other reasons There is a difference. When buying a product, you cannot choose the manufacturer at will. You should make a comparison to choose the product that suits you. After the aluminum foil paper and cash register paper are printed and coated, they need to be post-printed on the slitting machine to cut the large roll of semi-finished products into the required size. The semi-finished products running on the slitting machine are a unwinding and winding. The process includes two parts: the speed control and tension control of the machine. Slitting machine is a kind of mechanical equipment that cuts wide-width paper, mica tape or film into multiple narrow-width materials. It is commonly used in paper making machinery, wire and cable mica tape and printing and packaging machinery. Tension control refers to the ability to permanently control the tension of aluminum foil when it is conveyed on the equipment. This control must be effective for any running speed of the machine, including the acceleration, deceleration and uniform speed of the machine. Even in an emergency stop situation, it has the ability to ensure that the aluminum foil is not damaged at all. The so-called tension is to pull the aluminum foil and wind it onto the core according to the standard.
After reading the above, I believe everyone already knows the technical parameters of the slitter.