How are soft materials processed? Let's take a look with the slitting machine manufacturers.
There are several methods for cutting soft materials, such as plastic film and paper, which can be achieved by using blades, straight or round blades, while others will be cut The material is pressed against the hard roller.
Those cutting materials similar to narrow strips can be called coils when they are rewound, and the cutting blade can be set to the desired width. Some machines have many blades to increase the choice of cutting width, other machines have only one blade, and can be set to the desired position. The cut material is unwound on paper, plastic or metal core on the exit side of the machine.
This process is applied because of its low cost and high precision in mass production. Some machines have a program that monitors the blade and often grinds the blade to maintain the cutting quality and accuracy. Depending on the industry and the product being cut, these machines can operate between 10 m / min (special metal mesh) and 5000 m / min (paper making process). These machines can also contain a large number of automated functions to accurately control the tension of the material, automatically position the cutting knife, automatically align the winding core of the winding material, and reduce the manual operation of the coil.
After reading the above, I believe everyone already knows the processing principle of soft materials.
What is the correct maintenance posture of the paper slitter? Let's take a look below.
1. Lubrication of the oil path of the automatic slitting machine is an important part of maintenance work. Paper machine oil to keep the road clear, so that the automatic cutting machine can work efficiently and orderly.
2. Regularly change the oil of the automatic cutting machine and clean the oil line filter device to avoid part of the oil clogging.
3. Keep the parts of the automatic slitting machine clean, lubricated and flexible so that it can clear the accumulation of ink on the machine in time, so the production efficiency is high.
4. Keep the internal relay contacts of the electrical control box of the machine clean to prevent the machine from running normally due to too much dust.
The use of paper slitter can not be messed up, it has many taboos, so what are the taboos of paper slitter?
The power supply of the machine must be safely grounded during use, and the personal safety of the operator must be ensured. The speed of the host must be adjusted to the lowest speed when starting up, and then when the blade is installed, it must be prevented from being scratched by the blade. After using for a period of time, the non-woven slitting machine needs regular maintenance on the place where the machine is lubricated. There is also a double-sided sharpening system equipped with diamond material, and the blade cannot be disassembled, so it is used in Attention should also be paid to its maintenance in order to maintain the long-term sharpness of the blade.
After reading the above, I believe everyone already knows the taboo of the paper slitter.
If the blade setting of the paper slitter is not good, then the whole slitting process is prone to problems, then the slitting machine manufacturer will introduce how to set the blade for everyone.
1. The cutting edge of the blade should be kept sharp, and the cutting edge should be blunt or damaged. It should be sharpened or replaced in time. When multi-person operation is carried out, there should be a special person to command, and coordination should be coordinated. It is forbidden to cut two materials of different specifications at the same time on the round cutting blade, and overlapping cuts are not allowed.
2. The workpiece cut by the blade of the slitter must be placed steadily. Do not stack it too high or stack it in the aisle. Remaining materials and waste materials should be cleaned up in time to keep the site tidy.
3. When cutting into the material, it is forbidden to use the handle to promote the operation under the pressure plate. When cutting the short material, use another iron plate to hold it. When cutting the material, keep your fingers at least 200 mm away from the knife edge. After using the lever to match the wire, the lever should be withdrawn immediately before cutting. If the iron plate moves, use a wooden pillow to prevent it from popping out and hurting people after the pressure foot comes down.
After reading the above, I believe everyone already knows the blade setting problem of the paper slitter.
With the development of technology, the automatic slitting machine has also received great innovations. Let's analyze its advantages together.
1. There are two ways of winding: surface winding and center winding;
2. Unwinding photoelectric correction, high precision; divided into two files: manual file and automatic file;
3. Unwinding tension adopts automatic tension;
4. Adopt surface center winding, the winding quality is even and stable;
5. Circular knife slitting, reliable quality and convenient adjustment;
6. Fixed length automatic stop, length meter automatically.
The above is the advantage of the automatic slitting machine.