In the actual operation process, the sharpness of the blade should be kept at all times. If the blade is found to be blunt, it needs to be sharpened. During the cutting process, it is forbidden to cut two materials of different specifications at the same time.
        When cutting into the material, you can't put your hand under the pressure plate. When cutting short material, you should press it with an iron plate. When cutting, cut your fingers at least 200 mm away from the knife edge. After using the lever to match the wire, the lever should be withdrawn immediately before cutting. If the iron plate moves, use a wooden pillow to prevent it from popping out and hurting people after the pressure foot comes down.
         The position of the slitter should be flat, the cut pieces must be placed steadily, do not stack too high, and should not be stacked on the aisle.
        All in all, the paper slitter must pay more attention when operating.

        What are the fields of application of the automatic slitting machine? What does it need to check before using it?
        The common application range of automatic slitting machine is slitting of paper strips. This paper is slit. Make it into a product with flat area and uniform size. Therefore, it is particularly suitable for the production of related materials such as mica tape, paper, insulators and films. In which industries can the slitter be used? The use of paper mills, printing plants, and packaging plants is indispensable. The slitter is a machine that can operate at a high speed, and the operating speed can reach more than 300 meters per minute.
        Therefore, before using the equipment, you must carefully check the machine to see if the parts are damaged. If there is electricity, whether the machine can be operated (whether the power supply is energized). The operation of the conversion of the knife, because the requirements for the blade are relatively high, so before the machine equipment works, the blade must be checked. If there is no problem with these inspections, production can be carried out.
        The above is the use scope and inspection items of the automatic slitting machine.

        What are the analysis of product advantages of slitting machine manufacturers? The slitting machine has a trimming device, and the scrap is discharged by the fan; the product stands out after the survival of the fittest, and today's manufacturers are not comfortable with the status quo, but continue to innovate with the development of science and technology, and have been widely used today. At present, many manufacturers produce secondary products. In order to use them more safely and safely, you must read the relevant instructions before using them. The product is not only applicable to one industry, but is applied by many industries. The main features of the slitting machine are as follows:
        a. The surface center winding is adopted, and the winding quality is uniform and stable;
        b. There are two ways of winding: surface winding and center winding;
        c. Unwinding tension adopts automatic tension;
        d. Unwinding photoelectric correction, high precision; divided into two files: manual file and automatic file
        e. Round knife slitting, reliable quality and convenient adjustment;
        f. The fixed length automatically stops and the length is automatically metered; the large roll master roll is cut into products of different widths, and can have the effect of checking the product quality.

        What is the development and working conditions of the paper slitter? Let's take a look below.
        The mission power of the slitter is a comprehensive concept. In the slitting process, the stable tension system of the paper slitter is a main goal to ensure product quality. The magnetic powder clutch and brake are a special type of active actuator. The paper slitter is filled with mission gaps or films Cut into moments, changing the excitation current can change the magnetic state of the magnetic powder, and then adjust the transmitted torque. It can be used for stepless speed regulation from zero preliminary to synchronous speed. It is suitable for high-speed section fine-tuning and medium and small power speed regulation system. The paper slitter controls the tension between unwinding, pulling, slitting, and rewinding, so that the slitting data is always in a fluctuating state during the slitting process.
        Assuming that the tension control is stable, the paper slitter can prevent the original material from being deformed and drifting during the process of speeding up and speeding down. The pass will form the sum of the trouble of the next process and the tension of the unwinding shaft. Paper slitters used to use magnetic powder clutches to control tension. However, the speed of magnetic powder clutches cannot be high. When paper slitters are running, high-speed conflicts of magnetic particles are easily formed. Frequency conversion motor is used to control the tension system of the slitting machine. The swing roller is used for active detection. The man-machine is used for low temperature. The paper slitting machine shortens its life. When severe, it will be stuck and the machine will be blocked.
        With the development of technology and the composition of servo drive technology. It is to divide the raw material into several independent units. Its mission principle is to fix the raw material on the discharge. One end of the discharge shaft is equipped with a magnetic powder tension controller to stabilize the raw material. The required tension is passed through a pair of rubber rollers to pull the raw materials. The paper slitter is cut into several pieces by the blade. Then it is guided to the A and B winding shafts by each guide roller to stop the winding product.
        After reading the above, I believe everyone already knows the development of the paper slitter.

        The mission power of the automatic slitter is a comprehensive concept. During the slitting process, the stable tension system of the automatic slitting machine is a main goal to ensure product quality. The magnetic powder clutch and brake are a special type of active execution components. The film is cut into moments, and changing the excitation current can change the magnetic state of the magnetic powder, thereby adjusting the transmitted torque. It can be used for stepless speed regulation from zero preliminary to synchronous speed. It is suitable for high-speed section fine-tuning and medium and small power speed regulation system. The automatic slitting machine controls the tension between unwinding, traction, slitting, and winding, so that the slitting data is always in a fluctuating state during the slitting process.
        Assuming that the tension control is stable, the automatic slitting machine can prevent the original material from being deformed and drifting during the process of machine speed up and speed down. The pass will form the sum of the trouble of the next process and the tension of the unwinding shaft. Fully automatic slitting machines used to use magnetic powder clutch to control the tension, but the speed of the magnetic powder clutch cannot be high, and the high speed conflict of magnetic powder is easy to form during the operation of the automatic slitting machine. The vector variable frequency motor is used to control the tension system of the slitting machine. The swing roller is used for active detection. The man-machine is used for low temperature. The automatic slitting machine shortens its life. It will be stuck when severe, which will hinder the operation of the machine.
        With the development of technology and the composition of servo drive technology. It is to divide the raw material into several independent units. Its mission principle is to fix the raw material on the discharge. One end of the discharge shaft is equipped with a magnetic powder tension controller to stabilize the raw material. The required tension is passed through a pair of rubber rollers to pull the raw materials. The automatic slitter is cut into several pieces by the blade. Then it is guided to the A and B winding shafts by each guide roller to stop the winding products.