No matter which product is used, there must be matters needing attention when using the product. And when we ignore these precautions, problems that could have been avoided would easily occur. Therefore, we must do some safety checks before using mechanical products.
        Today we will talk about how to check the security of the paper cutter. There are many products of paper cutters, such as program-controlled paper cutters. And we said that we are introducing the program-controlled paper cutter. For the program-controlled paper cutter that is about to be put into use, the first thing to do is to check the previous operation record in advance for any debris on the blade surface, and to check the overall operation of the machine to ensure that it is safe before turning on. Secondly, it is necessary to strictly abide by the usage specifications during use.
        When the blade inside needs to be replaced, use a knife holder to ensure that the blade edge is in a closed state. Finally, before the two people who cooperate to open the safety cover and press the operation button at the same time, ensure that the machine is in a non-working state, otherwise the absolute safety of the operation cannot be guaranteed.

In the use of program-controlled paper cutters, safety issues are very important. Safety and operation habits are directly linked. Therefore, reasonable safe operating practices are very important. Let us focus on understanding the specifications of program-controlled paper cutters' safe operation.
1. When the equipment is turned on, mechanical inspection should be performed and safety inspections done, such as daily cleaning and refueling of oil holes.
2. After doing the above measures, when inspecting the photoelectric measures of the equipment, multiple operations should be performed to observe whether it is normal, and if abnormality is found, it should be eliminated immediately.
3. When operating a program-controlled paper cutter, you should work with all your heart and mind. Do not do anything unrelated to your job, so as not to distract you and increase the risk factor. Of course, two people are also prohibited from operating the equipment at the same time.
4. Don't put your hand into the machine during the operation of the equipment. If you can't use your hand to correct the fault, you must stop the machine first.
5. When using the equipment to cut paper, do not perform ultra-high operations to avoid accidents or operating loads.
6. When replacing the paper cutter of the equipment, it must first be stopped before it can be replaced.
7. In terms of equipment maintenance, it is sufficient to refuel and clean up the oil holes.
The above is the safe operation specification of the program-controlled paper cutter. In order to ensure the safety of everyone in the operation of the equipment, every operator should observe it.

        During the use of the program-controlled paper cutter, we not only need to pay attention to some matters in the operation of the machine, but also to the operator, there are some points to pay attention to. Below we will make some simple operating procedures for the operator of the paper cutter. Introduction.
        First of all, as far as the operator is concerned, he needs to have an understanding of the performance of the machine. Only after passing the examination and other formal operations can he formally operate; before opening, it is necessary to wear appropriate protective tools to avoid injury. Pay attention when starting Give the brake lightly, and then gradually accelerate. Lubrication is strictly prohibited during the rolling process of the equipment, and inspection and transportation of objects from the equipment is also prohibited.
        When our program-controlled paper cutter operators use electric hoists, they need to carefully check whether the steel ropes are intact, whether their limit switches are good, whether the hooks are hanging, and swinging is not allowed when lifting heavy objects. , Suspended in mid-air and other operations, when lifting a weight under its weight is also not allowed to pass by anyone. In addition, please pay attention that fireworks are strictly prohibited in the workplace, and do not use both hands when cutting paper.

          Program-controlled paper cutter is one of the more widely used in the printing industry.It is very convenient to use, safe and efficient, but sometimes it can not avoid the occurrence of some failures.For example, when its electromagnetic switch is damaged, it may cause its knife. The bed cannot be lowered during use.
         Sometimes, during the normal use of the program-controlled paper cutter, we may suddenly find that its knife cannot fall normally, and its cutter cannot fall.At this time, the red indicator display on its infrared photoelectric safety device is all on. Yes, but there are no obstacles on its corresponding surface. When we restarted the machine, it found that it was operating normally, but occasionally a similar situation occurred. After our careful analysis and inspection, it was found that an electromagnetic switch on the left side of the machine had failed. When we replaced the switch, the situation could be completely eliminated and the program-controlled paper cutter could work normally.

         Program-controlled paper cutter is an indispensable product in printing production, and has been praised by many users for its convenience, safety and efficiency. As with other equipment, failures will inevitably occur during use, which will cause certain adverse effects on production. Therefore, it is important to troubleshoot in time to ensure the normal operation of the machine.
         In the production process, sometimes the knife cannot be lowered, and the paper cutter cannot cut normally. At the same time, the photoelectric sensor control device also fails. At this time, if all the power is turned off and then on again, the photoelectric sensor control device can work normally and the paper cutter can be lowered, but the same failure will occur again after a period of work. In this way, the electromagnetic switch of the machine may be faulty. You can only replace the electromagnetic switch of the same specification and you can quickly resume normal cutting work.