What are the characteristics of slitting machine? The popularization of slitting machines in modern life has greatly improved production efficiency and accelerated the progress of modern society. The slitting machine manufacturers come to take you to know:
1. Equipped with high-precision correction device system to further ensure cutting accuracy;
2. Rewinding adopts 3-inch air-expansion reel and magnetic powder tension controller, the slitting operation is simple, the maximum winding diameter can reach 600mm; the winding is beautiful and tidy;
3. The cutting knife can use industrial surgical blade or flat knife (art blade) 18mm-1600mm adjustable knife;
4. The spindle and round knife use a stepless speed change system, which can be used as high and low speed control and positive and negative switching control; electronic speed control system is convenient and simple;
5. Equipped with double-sided diamond grinding and sharpening system; no need to dismantle to sharpen the knife to keep the blade sharp for a long time; to achieve the best cutting quality; with a vacuum loading capacity to keep the cloth and track clean;
6. The imported precision ball screw and slide rail are used to advance the cutting width in parallel, and the imported AC motor adjustment system steplessly adjusts and controls the cutting speed, thereby achieving high-precision cutting, and the accuracy can be controlled within 0.1 mm;
After reading the above introduction, did you understand it better?
The manufacturers of high-speed slitting machines were informed that in addition to the latest developments in classic statistical analysis, time and frequency domain analysis, time series analysis and parameter identification models, as well as refining technology, frequency, resonance demodulation analysis and cepstrum analysis, they also analyze and process Three-dimensional holographic spectrum analysis of the vibration signal of the cutting machine, axial trajectory analysis, short-time Fourier transform based on hypothesis and non-stationary signal, wing distribution and wavelet transform.
Through the existing microcomputer-based real-time online monitoring and fault diagnosis system and portable monitoring and analysis system, the development of virtual instrument technology, fault diagnosis equipment and instruments, and the development of virtual instrument technology are analyzed. Turn on the power and make sure the voltage, current and hydraulic system are correct and stable. Before the equipment is ready for operation, all personnel must notify the leaving equipment to ensure the personal safety of the personnel.
When running, do not touch the running film or roll to avoid personal injury. During operation, avoid cutting and cutting the core of each drum with a knife or hard object. The first package: Before the equipment is put into use, it must be ensured that the position is adjusted and lubricated. Check whether the tool is sharp.
After normal operation, the engine will run free of charge, check for any abnormalities, and then enter the order in advance. After work, the equipment should be adjusted in time according to the production conditions of the best working conditions to ensure medium pressure, cutting burrs, and the right side is lying flat. Ensure the smooth and precise cutting length of the cross-cutting machine on paper, increase the production management of vertical and horizontal cutting machines, continuously monitor the running status, and pay attention to the defects of wallpaper and products.
After the work is completed, clean the equipment dust and paper scraps in time, check the grinding wheel, the water in the oil purification water block and the water storage tank, and check whether the running parts are abnormal. Then, according to the instructions, turn off the power and maintain the computer operating system.
The paper cutting machine is composed of a frame, a transmission system, a receiving and discharging machine, a tension control device, a traction member, a slitting bracket, a waste winding and a discharging device. The transmission of the paper slitter is driven by the main motor to drive the rubber roller and the receiving shaft to operate synchronously to achieve the purpose of stretching and discharging the finished product. Let's take a closer look at:
1. Receiving mechanism and tensioning device: The receiving mechanism of paper slitter is mainly composed of chain, synchronous wheel, magnetic powder clutch and air expansion shaft. As long as adjustments are made, the two reels are controlled by one motor. The current of the magnetic powder clutch can change the tension of the receiving shaft.
2. Traction member: The traction member of the paper slitter is mainly composed of a pair of traction rubber rollers and a plurality of hard alumina rollers, which are used to take out the raw materials of the finished product. Power is obtained from the motor through V. The belt is transferred to the active traction roller for operation.
3. Slitting knife holder: The slitting knife holder of paper slitting machine has circular knife slitting and straight knife slitting. The operating handle can make the circular knife move slightly axially, and the circular blade and cushion can be adjusted by the plane cam. Groove shear gap.
4. Rewinding and discharging of waste: use the wind of the blower to discharge the waste through the wind pipe.
5. Discharge mechanism and automatic rectification: The discharge mechanism is mainly composed of discharge shaft, support block, cylinder, base, left and right moving seats, etc., and is composed of automatic correction device: photoelectric opening, correction guide roller, left and right bracket, correction moving plate and ball . Nuts and screws, synchronous motors and left and right limit switches.
6. Paper slitter frame and transmission system: The paper slitter frame is composed of left and right wall plates, supporting blocks and unloading mechanism. The transmission system is mainly used for pulling raw materials and winding finished products. It is driven by the variable frequency stepless speed regulation motor through the motor V belt to pull the rubber roller. The main traction rubber roller and the driven traction rubber roller are in close contact with each other. The traction material is driven, and the lower circular blade shaft is synchronously operated by the active traction roller to achieve better cutting requirements. The lower circular cutter shaft drives winding A and winding B to perform synchronous operation, so as to achieve the purpose of receiving material.
The paper slitter divides the raw material into several independent units. The working principle is to fix the raw material at the end of the discharge shaft, and install a magnetic powder tension controller to make the required tension of the raw material constant, and then pass through a pair of rubber rollers. Pull the raw materials and cut them into several pieces with a blade. Then, the guide roller is guided to the A and B winding reels to wind the finished product.
Many industries are familiar with slitting machines. Slitting machine is a device for longitudinal slitting of wide-width materials. We can understand the scope of its use to understand the role of the slitter. The type of paper is separate, which is also the type of use of the slitter. The manufacturer of the slitter will take you to learn more about:
It is used for strip metal coils, such as strip steel and stainless steel, mainly because steel processing plants, steel rolling mills, electrical industries, automobiles, and slitters in these industries play an important role.
Anyone who knows slitting machines knows that slitting machines are slitting machines, and it is also very versatile. Then I will introduce the working principle of the slitting machine. Through the specific understanding of the slitting machine, not only can it work efficiently while in use, but also effectively increase the service life of the slitting machine.
Slitting machine can also be used in leather, fabric, film and plastic industries. The structure of the slitting knife consists of unwinding, that is, unwinding and guiding positioning, slitting and slitting, and winding. Its main function is to cut wide-volume materials, that is, to convert the length of the wide-volume material into a narrow-sized coil, so as to prepare for future functional processing.
The slitting knife has many advantages and reasonable layout. This makes it particularly convenient and simple in operation, and has a high degree of automation, high production efficiency and high precision during work. Cold rolled, hot rolled coils, stainless steel plates, silicon steel sheets, color steel plates, aluminum plates and many large sheet metal materials, as well as circular blades are widely used in this field, and the work efficiency is also very high, so it is particularly popular.
The stable operation of the tension control system is the prerequisite for the slitter to complete the operation. The following slitter manufacturers will take you to understand the tension control system of the slitter:
Features:
1. Centralized panel operation, integrated circuit control. Each part of the machine is focused on panel operation control.
2. Main functions of the panel: A. Spindle speed adjustment B. Rewind length setting C. Unwind tension adjustment D. Rewind tension setting E. Start. stop button.
3. The cutting knife adopts upper and lower round knives, and the lower knife pad can be replaced according to different cutting widths, and the cutting width is adjusted to achieve high-quality cutting quality.
Magnetic powder brake device of slitting machine The unwinding group of the slitting machine is connected with the inflation shaft by transmission parts, and the speed of unwinding is controlled by controlling the torque of the magnetic powder brake. The main purpose of the magnetic powder brake of the slitter is to provide balanced and stable torque, which can be adjusted with the tension controller to improve the efficiency and quality of the slitter's unwinding work and the entire action.
The tension control of the magnetic powder brake is accurate and simple, which can prevent the slitter from unwinding the material. The magnetic powder brake of the slitter adopts DC24V DC voltage. The heat dissipation can be selected from natural cooling (air cooling) or forced cooling of the device fan. During installation, please keep the magnetic powder brake of the slitter on the horizontal shaft and the surrounding environment must not be too wet, etc.