What are the precautions for the automatic slitting machine, let's take a look:
Introduction to the installation and use adjustment of the paper computer slitter. After unpacking the machine, you should check the integrity of the machine and check whether there is damage during transportation. After checking the damage, you can install the calibration level on a flat and solid basis. , Check whether the parts are intact and intact, whether the connecting bolts are tightened reliably, and whether the moving parts are flexible. Then fill the lubricating parts with the corresponding lubricating oil. After checking the refueling, confirm that they can be turned on before reading. The attached manual. Run slowly at first when starting, and slowly increase the cutting speed until everything is normal.

        What exactly does the automatic slitter do? This article will give you a popular introduction:
The traditional control scheme of the slitter is to use a large motor to drive the rewinding and unwinding shaft. A magnetic powder clutch is added to the rewinding and unwinding shaft. The resistance of the magnetic powder clutch is controlled by adjusting the current of the magnetic powder clutch to control the surface tension of the material . Magnetic powder clutch and brake is a special kind of automatic actuator. It transfers torque through the magnetic powder filled in the working gap. Changing the excitation current can change the magnetic state of the magnetic powder, and then adjust the transmitted torque.
        It can be used for stepless speed regulation from zero to synchronous speed. It is suitable for high-speed segment fine-tuning and medium and small power speed regulation systems. It is also used in the unwinding or rewinding tension control system to adjust the torque by adjusting the current to ensure that the tension remains constant during the winding process.
        The main feature of the slitter is that the magnetic powder clutch acts as a resistance device. Through system control, it outputs a DC voltage to control the resistance generated by the magnetic powder clutch. The main advantage is that it is a passive device that can control less tension.
        The main disadvantage is that the speed cannot be high, and it is easy to cause high-speed friction of the magnetic powder during high-speed operation, resulting in high temperature, causing the magnetic powder clutch to heat up and shorten its life.

       The characteristics of the paper slitter are still very clear, but what are the characteristics, everyone must want to know, let's take a look together:
        1. The cutting knife can use industrial surgical blade or flat knife (art blade) 18 [2] mm-1600mm adjustable knife;
        2. The spindle and round knife use a stepless speed change system, which can be used as high and low speed control and positive and negative switching control; electronic speed control system is convenient and simple;
        3. Equipped with double-sided diamond grinding knife system; no need to dismantle to sharpen the knife to keep the blade sharp for a long time; achieve the best cutting quality; and with a vacuum loading capacity to keep the cloth and track clean;
        4. The imported precision ball screw and slide rail are used to advance the cutting width in parallel, and the imported AC motor adjustment system adjusts and controls the cutting speed steplessly, so as to achieve high-precision cutting, and the accuracy can be controlled within 0.1 mm;
        5. Equipped with high-precision correction device system to further ensure cutting accuracy;
        6. Rewinding adopts 3-inch air-expansion reel and magnetic powder tension controller, the slitting operation is simple, the maximum winding diameter can reach 600mm; the winding is beautiful and tidy;

The high-speed slitting machine is widely used in modern production and is popular with consumers. So what is he? This article will give you a popular science:
The slitting machine is mainly used for slitting the large roll master roll into products with different widths, and can have the function of checking the product quality. Its main features are as follows:
1. Fixed length automatic shutdown, automatic length metering;
2. There are two ways of winding: surface winding and center winding;
3. The tension of unwinding and unwinding adopts automatic tension control; the control methods include tension feedback control and taper control.
4. Two cutting tools, round knife cutting and air knife cutting, with reliable quality and convenient adjustment;
5. Using the surface center winding, the winding quality is even and stable;
6. With trimming device, the trim is discharged by the fan;
7. Suitable for slitting narrow strips (insulating materials, mica tapes, films, etc.) of various thin coils
8. Unwinding photoelectric correction, high precision; control mode is divided into two files: manual file and automatic file.

        Paper slitting machine is a kind of mechanical equipment that cuts wide-width paper, mica tape or film into multiple narrow-width materials. It is commonly used in papermaking machinery, wire and cable mica tape and printing and packaging machinery. The main application of the slitting machine: non-woven fabric; mica tape, paper, insulation materials and various film materials, especially suitable for the narrow band (non-woven fabric, paper, insulation materials, mica tape, film, etc.) cut.
        1. The slitting length can be set continuously. If there is an error in the actual slitting length, it is easy to calibrate by setting parameters.
        2. The slitting control of the paper slitting machine is divided into static and dynamic slitting: when the set length is reached, the machine is stopped accurately, and then the static slitting is processed, and then restarted after the slitting; when the set length is reached, no The cutting signal is issued when the machine stops, and the cutting machine dynamically cuts and processes during the movement of the material.
        3. The paper slitter needs to cut the whole roll or the whole raw material with a fixed length, such as plastic packaging materials, packaging cartons, steel plates, films, leather, wood chips, etc., all of which need fixed length cutting. control.