A magnetic powder clutch is added to the winding and unwinding shaft, and the aggressive control scheme of the slitter is to use a large motor to drive the winding and unwinding shaft. By adjusting the current of the magnetic powder clutch to control the resistance generated by it, to control the tension of the data surface. The magnetic powder clutch and brake are a special type of automatic actuator. The magnetic powder filled in the working gap transmits torque. Changing the excitation current can change the magnetic state of the magnetic powder, and then adjust the transmitted torque. It can be used for stepless speed regulation from zero to synchronous speed. It is suitable for high-speed segment fine-tuning and medium and small power speed regulation systems.
There are many types of slitting machines used in daily operations. In this case, it can better meet the actual use needs. Take the automatic slitting machine as one of the types. Their use That's a lot. This automatic slitting machine is a type of mechanical equipment that is easy to operate, and it can bring great convenience when it is used. There are also many styles of design, and the type of vertical design is one of them. They are used a lot.
The sides are smooth and the operation is stable: the paper roll is firmly wound. Low noise. Easy to operate: the slitted paper tape is smooth and smooth on both sides without burrs. Strong adaptability: the upper and lower blades can be adjusted at any width between 2 and 1600mm. High output: The output of a single machine can be used for 3 tube rolling machines. Before starting, ensure that the voltage, current and hydraulic pressure are correct and stable. Before the equipment is ready for operation, all personnel must notify leaving the equipment to ensure personal safety before starting operation. During operation, do not touch the film roll or roller core in operation with your hands to avoid personal injury caused by rolling your hands. During the operation, do not scratch or cut each roller core with a knife or hard object.
The current slitter has the above advantages. It is precisely because of these advantages that it can make their performance better, and they can be well demonstrated during the operation. Take the full-automatic high-speed slitting machine equipment, it belongs to such a type of equipment. They are used a lot, and they can be well displayed in the process of use. During operation, their flexibility is very high, and the corrosion resistance and stability of the machine itself are also very good.
The most common application range of slitting machines is slitting of paper strips. This paper is slit. Make it into a product with a flat area and a uniform size. Therefore, many of the most common businesses listed in shopping malls will often use it mainly to cut horizontally or vertically wide data. It is especially suitable for the manufacture of mica tape, paper, insulators and films. What kinds of occupations can be applied to the slitting machine? The use of paper mills, printing plants, and packaging plants is indispensable. The slitter is a machine that can operate at high speed, and the operating speed can reach more than 300 meters per minute.
The aggressive control plan of the slitter is to use a large motor to drive the rewinding and unwinding shaft. A magnetic powder clutch is added to the rewinding and unwinding shaft, and the resistance generated by the magnetic powder clutch is adjusted to control the tension of the data surface. Magnetic powder clutches and brakes are a special type of automated fulfillment component. The torque transmitted through the magnetic powder filled in the working gap can change the magnetic state of the magnetic powder by changing the magnetic current, and then adjust the transmitted torque. It can be used for stepless speed regulation from zero to synchronous speed. It is suitable for high-speed section fine-tuning and medium and small power speed regulation system. It is also used to adjust the torque by adjusting the current to ensure that the tension during the winding process adheres to a constant unwinding or rewinding tension system.
Add lubricating oil; when checking and disassembling the automatic slitting machine, the main parts of the automatic slitting machine should be checked before use. It is forbidden to use inappropriate things and choose unscientific operation methods; make a comprehensive review and review of the machine every two weeks; if the automatic slitting machine is not used for a long time, all the bright appearance must be scrubbed and cleaned Rust oil, plastic cover to hide the whole machine. If the full-automatic slitting machine is stopped for more than 3 months, the anti-rust oil should be covered with moisture-proof paper; after the operation is completed.
Clean the equipment carefully, scrub and clean the exposed friction surface, and add lubricant. It is necessary to suspend the regular and irregular inspection of the rolling parts (especially the real-time monitoring of the wearing parts), implement timing adjustment, timing conversion, commutator and make detailed records to achieve the intention of extending the life of the equipment. The performance of the current slitting machinery is even better. They are all fully automatic equipment types. When they are used, they can bring high value and use.
Automatic cutting machine is often used in paper making machinery, wire and cable mica tape and printing and packaging machinery. The main application of slitting machine: mica tape, paper, insulation materials and film slitting, especially suitable for slitting narrow bands (insulation data, mica tape, film, etc.). Features of slitting machine: The main feature of slitting machine is that magnetic powder clutch is used as a resistance device. Slitter is a mechanical device that slits wide paper, mica tape or film into multiple narrow materials. After system control, a DC voltage is output to control the resistance of the magnetic powder clutch.
The first advantage is that it is a forced device that can handle smaller tensions. Before use, the fully automatic main parts should be inspected and filled with lubricating oil; when checking and disassembling the automatic slitting machine, it is forbidden to use inappropriate things and choose unscientific operation methods; make a comprehensive arrangement of the machine every two weeks. View. The performance of such equipment in our company is very good in the process of use. There are also many automatic equipments, and they can also be controlled on the computer during operation.