1. The product to be constructed on the laminating machine must be straight. Deal with uneven paper with "ruffles" and "tight edges". "Ruffle edge" paper can be baked, and "tight edge" paper can be hung.
2. Be sure to wait for the blot to dry before covering it, otherwise it will cause blistering or hairiness.
3. Spray powder as little as possible during printing, otherwise it will cause emptiness and blistering at the pile of powder. The powder spraying should be removed before laminating, the ones with more prints can be hung to remove the powder, and those with less prints can be wiped manually.
4. Pay attention to the direction of paper strands when laminating machine, especially thick paper, to reduce the curling phenomenon of paper due to rolling and stretching.
1. Professional multi-function laminating machine, which can do various work such as thermoplastic, cold laminating, low temperature cold laminating, thermal laminating, etc., suitable for graphic mounting and binding cover mounting;
2. The pressure and height of the rubber roller can be adjusted integrally on one side; the internal heating type double roller heating, intelligent constant temperature;
3. Light touch operation buttons, free temperature setting, 9 speed adjustment, LED digital display;
4. The upper and lower roll film supports can be heightened, and large roll thermal film can be installed to avoid the inconvenience caused by frequent replacement of roll film. The tension of the upper and lower roll film and the left and right sides of the roll film can be adjusted separately to ensure that each Laminating effect of various materials;
Due to the heat of the image, the color of the image of the plastic laminating machine will be stronger than that of the water transfer, and it will not fade easily. It has corrosion resistance, impact resistance, aging resistance, and It has the characteristics of grinding, high temperature resistance, fire resistance, and can keep the color for ten to decades. Therefore, the thermal transfer technology is especially suitable for appliances, daily necessities, building materials and other objects that have special requirements for image retention. For example, thermal transfer technology can be used to print trademarks, barcodes, and labels on commodities.
In terms of market demand for trademark laminating machines, with the continuous development of the commodity economy, various manufacturers and departments have higher and higher requirements for the trademark, label and packaging beauty of their own products. For the printing industry, the concept of printing is no longer The traditional paper in people's impression is printed. From our daily necessities to office appliances, to products in various industries such as telecom, decoration, and craftsmanship, we need more, better and more practical external packaging, and most of these packaging are realized by transfer printing. , So the transfer industry has a very broad and deep market space.
The film used in the thermal laminating process of our laminator mainly includes polyester film and polypropylene film. Generally, polypropylene film is used when covering thinner films, and thicker polyester film can be used for printed products that require additional protection. Material market. The price of polyester film is more expensive than polypropylene film, but it has high strength and can protect the printed products better. If both sides of the printed product need to be laminated, it is best to use polyester film equipment consumables. In the lamination of digital printing products, it is mainly necessary to avoid problems such as curling of the printed product after lamination in Central China. Therefore, if conditions permit, cover both sides of the printing material as much as possible; if only one side of the paper is coated without the other side, curling is very easy to occur. However, it should be noted that only single-sided lamination can be applied to the cover of the perfect binding book. Never cover the second and third front cover, otherwise the book block and the cover cannot be firmly bonded to the printing technology.
Secondly, we also need to figure out the following two questions before laminating:
1. What problem do you plan to solve for the customer?
2. Where are the technical points of the laminator?
Printers use both cold adhesive and hot adhesive technologies to complete large-volume laminating work. They can use one technology alone or a dual system. Generally speaking, hot-adhesive film is the most common and the cheapest. It is divided into three different types of film materials: polyester (PET), polypropylene (OPP) and nylon.
In order to make the product of the laminating machine not wrinkle after folding, you can choose OPP film. Regarding the selection of laminating materials, since laminating may affect the color reproduction of digital printed products, this is mainly because the films used in laminating are not necessarily 100% packaging machines or transparent films, so the color balance influential.
The main factors affecting the anti-counterfeiting performance of the laser holographic trademark of the trademark laminating machine are the type of trademark and the location of the trademark. Different types of laser holographic image anti-counterfeiting trademarks have different anti-counterfeiting effects. Even the same kind of anti-counterfeiting trademarks have different anti-counterfeiting effects due to different locations.
The laser holographic image anti-counterfeiting trademark of the trademark laminating machine is very convenient to use and has good adaptability to the labeling machinery. Because of the different application of glue and other adhesives, there will be no stains on the production line, especially for the packaging of higher-end hair. The effect is more obvious. This trademark is currently the largest in use. But it has a fatal shortcoming that it can be used repeatedly. After being removed from the lower position, it can be completely glued to another position, so that some criminals can use the old packaging and trademarks to counterfeit, thus affecting the anti-counterfeiting effect. From the perspective of anti-counterfeiting, such trademarks should not be used as anti-counterfeiting trademarks. Therefore, some people in the industry have introduced higher-tech laser holographic image technology, hoping to improve its anti-counterfeiting effect. Is this effort effective and worth it? We can get a clear answer by looking at the degree of production of anti-counterfeiting trademarks by the trademark laminating machine.