1. Operate reasonably in accordance with the rules of the manual and prohibit all improper operations
2. Regularly check the parts of the laminating machine to see if it is damaged, and replace it immediately if it is damaged
3. For the water coming from the flower planter, when the earth shovel is lowered, the height of the ridge can be increased, but at the same time, the sowing opener and the depth-limiting roller barrel should be raised to the corresponding parts. At the same time, the sowing opener and the depth-limiting drum should also be adjusted down to the corresponding position. A good laminator, not only requires the operation specification, but also the maintenance is equally important, strictly follow the laminator operation and maintenance regulations , Develop a good habit of using the laminating machine in order to extend the life of the machine.
1. Fully automatic laminating machine will cover the film on the picture to improve the strength of the picture and the wear resistance of the surface.
2. Isolate the picture from the outside air to prevent deformation and cracking caused by corrosion, humidity, and drying of corrosive gases in the atmosphere, fading and discoloration caused by rain erosion and ultraviolet radiation, and the computer bronzing machine maintains the bright and luster of the picture screen. No decline, extend the life of the picture display.
3. Paste the picture on the display board or fabric to make a hanging advertising screen
4. Fully automatic laminating machine presses a special mask or sheet on the picture to form a picture with special artistic effects such as light, matt, oil painting, virtual and three-dimensional.
1. The product to be constructed must be straight. Handle uneven paper with "ruffled edge" and "tight edge" phenomena. Paper with "lotus edge" can be baked, and paper with "tight edge" can be hung to dry.
2. Be sure to wait for the blot to dry before coating, otherwise it will cause blistering or hair pulling.
3. Spray as little powder as possible during printing, otherwise it will cause emptying and bubbling at the powder pile. Before spraying the film, the powder should be disposed of. If the number of prints is large, the powder can be hung to remove the powder. If the number of prints is small, the powder can be wiped manually.
4. When laminating machine, pay attention to the direction of paper strands, especially thick paper, to reduce the phenomenon of curling caused by rolling and stretching.
Temperature is the primary factor of pre-coating film, because the adhesive on the pre-coating film is hot-melt adhesive, the temperature determines the melting state of the hot-melt adhesive, and determines the hot-melt adhesive molecules to BOPP film, printed ink layer, paper, etc. Penetration and diffusion capacity. Although the increase of the coating temperature helps to increase the bonding strength, too high temperature will cause the film to shrink, the product surface will shine and blisters, and the product will wrinkle. According to practical experience, the temperature of the film should be controlled between 70 ~ 100 ℃.
The surface of the paper of the laminating machine is not flat. Only under the appropriate pressure, the hot-melt adhesive in the molten state can completely cover the surface of the printed product, the laminating product is bright, and the bonding effect from the laminating machine is good. The pressure is small, and the bonding is not strong; the pressure is higher, which helps to improve the bonding force between the film and the paper product. However, if the pressure is too high, it is easy to wrinkle the product, and it is easy to damage and deform the surface of the rubber roller and reduce the service life of the rubber roller. As the pressure increases, the contact pressure between the rubber roller and the heating roller increases, which increases the load on the shaft head and bearing of the two rollers of the laminating machine, which increases the wear and aggravates the load on the transmission system. Too much pressure will affect the service life of the whole machine.
Set one within 50 meters according to the continuation length of the automatic laminating machine, and it should be satisfied that the transition resistance on the laminating machine in the furthest point from the ground electrode does not exceed the requirement of 10 ohms. The ground resistance must not exceed 20 ohms. The ground electrode is buried at the highest point of the ground, and is not shallower than 50 cm above and below the ground. When filling, the new fill should be rammed.
The vertical column of the automatic laminating machine is required to be vertical. The vertical error of each corner column shall not exceed 0.5%, and the neutral column shall not exceed 1%. The distance between the columns of the external laminating machine constructed in eight layers shall not exceed 2 meters. The vertical spacing is not more than 1.8 meters, and it is necessary to use the members to join together, tighten the bolts, and the longitudinal degree of the load-bearing bar must be supported on the cross bar.