The paper cutter is a very convenient product. The cutting of the paper makes the paper have various sizes and is used in all aspects of life. So what does the paper cutter need to pay attention to?
In general, the most important aspect of a paper cutter when cutting paper is to pay attention to the angle of the cutting edge. The selection of the cutting edge angle is a very important part of the cutting work. After selecting the most appropriate angle, cutting can have a multiplier effect, and the cut paper is relatively flat and standard. Many paper cutter users often ignore this, which will cause more damage to the paper cutter.
Due to the incorrect cutting method, method, and angle of the cutting blade of the paper cutter when cutting the paper, the impact force increases during the cutting process, causing the safety screw to loosen, causing breakage and other various machinery destroyed. These are very disadvantageous factors for the paper cutter.
Today, I will teach you the correct operation of the blade of the paper cutter. In this way, you can avoid accidents. I hope Xiaobian's answer can be helpful to everyone.
When changing the cutter first, first turn off the main motor, wait for about 2 minutes, and confirm that the transmission belt has completely stopped. Put the two wooden cutter changers under the blade, and set the cutter selection switch on the switch panel. At the tool change position, the knife function selection switch must be in the cutting position. Use a sleeve to rotate the nut on the end face of the pulley, remove all the connecting screws on the blade, and then use an Allen wrench to push the knife-hanging device inward for about 4 millimeters. The brake of the knife device is disengaged, and the rotary knife hanging device makes the blade fall smoothly on two wooden knife changers. Install two knife change handles, remove the knife, and pay attention to supporting the knife to prevent overturning and hurting people.
In order to ensure the cutting quality of paper and printed matter, it is usually necessary to maintain the cutter. What are the main points of the daily maintenance of the cutter?
According to different seasons, choose the right hydraulic oil. No. 20 oil is used in winter to maintain its fluidity; No. 30 oil is used in summer to maintain its viscosity.
Maintain proper hydraulic pressure. Excessive pressure will cause the seal to burst; if the pressure is too small, the cutting of the blade appears sluggish. Use talcum powder or paraffin to coat the cutting platform and blade opening. By doing so, one is to reduce the frictional resistance between the paper and the platform, and the operation is labor-saving; the other is to extend the cutting times of the blade, and the cutting edge is smooth and neat.
Fill with lubricant. Lubricate the machine at the oil filling port before work to keep the machine lubricated and clean without noise, so that the paper cutter is always in good working condition. The above methods must be kept in mind, so that the cutter can be better protected and maintained, and its service life can be extended.
During the use of the paper cutter, sometimes "cutting knife" failure occurs, which seriously affects the normal work of the paper cutter. If you want to eliminate this problem fundamentally, you must start with improving the structure of the cutting system of the paper cutter. This is not something that ordinary users can do. For ordinary users, you want to eliminate or reduce "Knife" failure should pay attention to the following aspects:
1. Sharpen the blade in time to keep the blade sharp. In addition, if not necessary, try not to use blades with large corners. This can effectively reduce the cutting resistance of the paper.
2. Pay attention to the change of the slide gap. When the phenomenon of "cutting the knife" becomes obvious, you should first check the change of the slide gap. Under normal circumstances, the gap should not exceed 0.1 mm. The sliding surface is subjected to a large load during the cutting process, coupled with poor lubrication conditions, and is constantly worn during use, causing the gap to increase, which causes a “cut out” failure. When the confirmation gap exceeds the allowable value, it should be adjusted in time.
3. Careful maintenance to ensure good lubrication of the slide surface.
Cutting machine performance advantages:
1. The paper cutter has high pressure, accurate paper cutting, and the paper cutting accuracy is about 25C.
2. Paper cutter has high pressure, adjustable pressure, and fast cutting speed!
3. The guide rail controls the paper pusher to prevent the paper from moving, which is smooth, reliable, and durable.
4. The paper cutting machine's computer-controlled pusher automatically pushes the paper continuously and quickly, without manual positioning at all, changing the entire cutting process, and cutting speed is fast.
5. Computer resolution is 0.01mm, paper cutting is more accurate. (Note: computer program control is not an intelligent digital display)
Paper cutter configuration features:
1. Computer automatic control, 5.7-inch (optional 12-inch true color touch screen) blue-screen LCD display, data resolution up to 0.01mm, paper pushing speed up to 9m / min.
2. Paper guide rail pushing structure.
3. Wheel or worm gear transmission structure.
4. Secondary pressure, high pressure, adjustable pressure.
5. The tool changing device is safe and fast.
6. Paper cutter air cushion, chrome plating, with photoelectric protection.
7. The frame is made of ductile cast iron, which is sturdy and durable.
8. Lubrication system in paper cutter.