The automatic paper tube machine has an intelligent paper tube machine with a self-locking function. After the angle of the swing arm is adjusted, it can be automatically locked without shaking. With automatic cutting device, the cut is neat and without warping, and the length of the cutting camp is adjustable. Analysis of common faults when using paper tube machine equipment.
1. The spiral of the paper tube machine is uneven. This situation can be considered from three aspects: it may be that the cutting blade of the paper tube machine equipment has too much resistance to the paper tube; when the lubricant is applied, the layer of lubricant is not uniformly applied; Insufficient belt tension, etc.
2. The distribution of paper tube adhesive is uneven. It is possible that the blades and paper strips of the paper tube machine equipment did not form a right angle; the blades used by the equipment were not clean enough and there was debris stuck on them, which caused uneven coating. In this case, the angle of the scraper and the paper tape should be adjusted appropriately, and the scraper should be cleaned in time.
3. The amount of adhesive coating is unreasonable. Whether it is too much or too little, it will bring adverse effects. In view of this situation, it is necessary to appropriately adjust the blade angle of the scraper in accordance with the actual situation, so that the paper tube machine equipment can maintain a normal state.
The features and functions of the paper tube machine include automatic cutting and automatic tube dropping, automatic paper stop function when paper is cut and paper cut; automatic speed change and automatic recovery when cutting; computer PLC control with remote control port; multi-point operation panel or digital remote control function, very convenient operation The circular knife actively cuts, the cut is more stable, and the performance is more stable; more than eighty function settings, the machine operating conditions can be set arbitrarily.
The working principle of paper tube machine:
Paper tube machine adopts CNC computer numerical control system, SMS synchronous mobile cutting and cutting device, equipped with imported servo drive, can greatly reduce the resistance of the cutter to the paper tube during the cutting operation, and make the gap of the paper tube uniform.
The blade of the paper tube machine adopts imported single circular knife cutting design, and the fully CNC-driven cutter (non-cylinder driven) achieves accurate cutting. The ultra-quiet design of the transmission part of the paper tube machine improves the work efficiency!
Warm reminder that the development of products cannot be separated from the progress of science and technology. Today's products are incomparable. It is used in many industries. However, it does not mean that it can be easily operated when it is installed and used, but it should also be performed in accordance with the formal instructions!
Note that when operating the paper tube machine:
1. Adjust the cutter and clamp the work before cutting.
2. The parking baffle must be fixed, and work can only be carried out after a test run of clamping, loosening, forward and backward.
3. When the machine tool is rotating, no part of the human body should touch the transmission parts. Cuffs must be worn during operation, and gloves are strictly forbidden to work.
4. Spindle speed must be changed after stopping. Gears must be fully engaged during shifting.
5. When the machine is found to be abnormal, stop the machine immediately for inspection. When the long material pipe is put into the material rack and the lead wire is loosened, measures should be taken to prevent the pipe from rolling, impacting and crushing people.
6. Check that the dust removal device is intact before cutting.
7. When using a wheel cutting machine, check in advance whether there are any flaws, cracks or moisture on the wheel, and whether the power cord is reliable. When changing tools, measuring workpieces, lubricating, and cleaning pipe heads, it must be stopped.
The paper tube machine should pay attention to many details when using it. Let's take a look at how to use the paper tube machine correctly:
1. Before using the equipment, check the conditions of each department in detail, whether the electrical equipment and switches are good, whether the electrical circuits are insulated, whether the screws and nuts are tightened, and whether the protective devices are safe. Operate for 1-2 minutes. The equipment can only be operated after it is normal.
2. The equipment must be specially responsible, and it is strictly forbidden for others to misappropriate it. It is strictly forbidden to place workers, cards, measuring tools and other sundries in various parts of the machine tool during work, and staff must not leave the work place without permission.
3. When cutting low, if you use a ventilation machine to cut paper, the cutting height cannot exceed 125 mm, and according to the size requirements, use a flat iron to fasten it. The machine tool can only cut paper, not other plates. It should be operated by two or more people, and they should cooperate with each other. When working, do not put your hand under the iron and the blade to prevent cutting injury. If using a special paper cutter, do not put your hand into the rotating mandrel to prevent crushing.
4. When edging, prevent the trousers from being caught in the paper loading shaft. When adjusting the machine, pay attention to the abrasive cloth wheel.
Paper tube machine, as its name implies, is the machine and equipment for producing paper tube. The paper tube produced is used in various industries, chemical fiber industry tube, film industry tube, printing industry tube, paper industry tube, leather industry tube, food. Packaging tube, construction industry tube, exhibition industry tube, etc. There are also many types of paper tube machines. The most common paper tube machines are spiral paper tube machines and roll paper tube machines.
Employees need to pay attention to: whether it is a paper tube machine or other types of machinery and equipment, employees must comply with certain safe use rules when using, only in this way can ensure their own safety. Before using the paper tube machine, the operator should wear personal protective equipment properly. For example, the paper tube requires a female worker to wear a protective cap during processing. If not, the hair may be twisted in. It is also required not to wear gloves. If it is worn, the rotating part of the paper tube machine may twist the gloves in to prevent hands from being injured.
Requirements for correct machine operation:
The paper tube machine should also perform safety inspection in accordance with regulations during operation. In particular, look at the fastened items to see if they are loose due to vibration. Once they are loose, fasten them in time to prevent unnecessary safety hazards during operation.
Before the operation, the paper tube machine should be inspected for safety, and it should be run empty. After confirming that it is normal, it can be put into operation. In addition, it is strictly forbidden to operate the equipment with faults. Do not make use of it to prevent accidents.