With the development of modern science and technology, new computerized paper cutters have replaced old-fashioned old paper cutters, but many people are not clear about the difference between the two. Now let the editors analyze it for everyone.
Computer paper cutter:
1. Has the characteristics of high precision, positioning accuracy of 0.01mm;
2. High efficiency, computer-controlled positioner automatically advances, retreats and high-precision positioning, the efficiency is doubled;
3. Low labor intensity, you can complete all the operations at one time, no need to move back and forth because of the difficulty of positioning;
4. Chinese operation keyboard, easy to learn, simple and easy to understand, you can see it at a glance;
5. The transformation cost is low, and the performance-price ratio of the program control system is very high;
6. Smart computer program control system with instructional programming, so that you don't need to learn programming, as long as you operate according to your past work mode, the computer will record your operation and automatically generate working procedures.
Computer paper cutter is an indispensable cutting tool in our daily life. So how do we use a computer paper cutter to sharpen, unload and install knives?
If we use a paper cutter to cut the paper, we find that the cut paper has burrs or is impervious
Then you need to sharpen the knife. The specific operation steps are to drop the knife halfway, remove all the screws that install the knife at shutdown, and then take out the handle of the knife to turn it up. After removing the screws, take the knife to the relevant sharpening place to sharpen the knife. Half of the sharpened knife is narrower than the original knife, so you need to lower the knife a bit, first put a piece of A4 paper under the knife, when the knife falls to the lower position, cut off the power and loosen the screw of the upper knife At the top of the knife holder, there are three knife adjustment screws. Take an internal hexagon and press down until the paper under the knife is cut through.
1. The blade is not sharp enough.
2. The sliders on the left and right sides of the knife holder are worn.
3. The safety screws are not often tightened.
4. The installation direction of the safety screw is wrong.
5. The two end faces connecting the safety screw are not flat due to deformation.
6. The blade is too deep into the blade or the grinding of the blade is not straight.
The blade adjustment starts from the installation. First, confirm that the machine is in a stopped state and cut off the power. Place the sharpened paper cutting machine blade on the tool changer, push the tool changer to the front knife bed of the paper press, adjust Cut the selector switch to the tool change position and turn the knife hanging device, raise the blade and tighten the connecting screw, then loosen and remove the tool changer, tighten the remaining fastening bolts, and the tool change is completed.
The adjustment of the paper cutting machine blade is to adjust the cutting amount of the blade to avoid cutting the blade too deeply and damaging the blade due to the height of the newly replaced blade. The blade adjustment steps are: first manually rotate the transmission wheel to determine the blade cutting depth, the knife bed moves to At the lowest point, carefully observe whether the cutting depth is reasonable. Under normal circumstances, the normal cutting is 0.5-1 mm; if the blade edge is in contact with only one end of the blade, you can adjust the eccentric shaft behind the main frame; if the regrinded blade cannot cut the paper The blade can be moved down until the paper can be completely cut, and the top knife cam can be manually rotated to make the blade cut the paper; the adjusted blade can be used for trial cutting with waste products, and then the normal work is performed after the sample is normal.
1. The operator must tie up the hem and corners of the clothes, tie up the cuffs, and ensure that the items in the pockets are empty. It is strictly forbidden to wear hanging ornaments to operate the machine;
2. The mental state of the operator must be good, and it is strictly forbidden to go to work under the condition of excessive fatigue, drinking or illness;
3. Clean up the debris around the paper cutter, place the materials to be cut in a suitable position, and check if any tools are left on the machine;
4. Check whether the switch is normal after starting the machine. Reliability, whether the cutter is sharp, try the knife three times, observe whether there is a return knife, if problems are found, it should be eliminated in time; check whether the connection of the cutter is loose, and the protection device Whether it is malfunctioning, etc., to ensure that the machine is running in a zero fault state.